Accessories Direct reading laser grade rod   We think this two piece 10' direct reading laser rod is the best thing since sliced bread. The sliding tape is marked in feet, tenths, and hundredths and also gives cut and fill measurements. Simply set the rod on a point with a known elevation, move the receiver until it gives an on grade reading, then move the tape until the known elevation is aligned with the pointer on the receiver clamp. The tape can then be locked so it is stationary with respect to the lower portion of the grade rod. To take further readings, slide the receiver or the upper rod portion until the on grade signal is given, then read the elevation off the tape. There is no need to add or subtract numbers to get your elevation. The receiver bracket fits Pro Shot R7, and R8 laser receivers.   Laser Rod, 10' Direct Reading:    $185.00 US List   Receiver Bracket for Laser Rod:    $65.00 US List T2 Aluminum telescopic Laser tripod   The T2 is a flat-head aluminum telescopic leg laser tripod with a 5/8 x 11 thread. It adjusts from about 3-1/2 feet to 5-1/2 feet in height. The telescopic leg segments are secured by quick release levers. T2 Tripod: $85.00 US List W1 Wall & vertical Laser mount   The W1 is designed to clamp to the wall angle on drop ceiling jobs, or can be used to lay a laser down into the vertical mode. In vertical mode, the W1 can be set on the floor, or threaded onto a tripod. (The L3, L5, L6, L4.7 and L4.7 Magnum lasers can all be used in the vertical mode.)  Note: the L6 laser does not require a vertical mount when used on a flat surface. W1 Wall & Vertical Mount: $75.00 US List Rechargeable Laser battery Kit   500-0250M NiMH Rechargeable Battery Kit (US) for Alpha, AS2, AS2 Magnum, L4.7 and L4.7 Magnum lasers $70.00 US List 080-0050M NiMH Rechargeable Battery Kit (US) for L6, L5 and L3 lasers $52.00 US List Contact Laser Reference for information on chargers for use outside the US. RC-1 Remote control for the L6 laser   The RC-1 is a full function, indoor use, remote controller for the L6 construction laser.  A major advantage over many other remotes, the RC-1 can turn the L6 laser fully on, or off.  The RC-1 allows you to change from 360º rotation to scan mode, adjust the width of the laser scan area and aim the scan area to a specific location.  Laser rotation speed is also fully controlled by the RC-1. RC-1 Remote Control: $100.00 US List MT1 Magnetic Laser ceiling target   The MT1 target magnetically attaches to steel drop ceiling wall angle or grid, and can be used with any visible beam rotating laser. MT1 Magnetic Ceiling Target: $12.00 US List S2 Compound slope adapter   The S2 Compound Slope Adapter allows the model AS2 laser to be setup to project a compound (dual) slope. An included chart provides information to guide the user through the setup, once both slopes for the site are known.  For slopes not covered by the chart, please click the link below to an Excel spreadsheet slope calculator where you can enter any slope values you wish. S2 Compound Slope Adapter: $50.00 US List P1 Plumb plate   The P1 Plumb Plate enables positioning the L4.7 Magnum construction laser over a point on the floor, so that its plumb laser beam can transfer that point to the ceiling, or for other plumbing operations such as elevator shaft control. P1 Plumb Plate: $10.00 US List Laser Reference, Inc.  •  USA Toll Free 1.800.238.0685 VM2 Vertical Laser mount   The VM2 is a basic vertical mount that works well with the L4.7, L4.7 Magnum, L5 and L3 lasers for plumb alignment and layout tasks.    Note: The L6 laser does not require a mount for basic vertical operation. VM2 Vertical Mount: $40.00 US List